发布时间 : 2024/5/19 14:27:15 星期日 文章Aruba2400无线控制器基本操作命令更新完毕开始阅读97e880805fbfc77da269b14b

Aruba2400无线控制器基

本操作命令

Aruba2400无线控制器基本操作命令

(Aruba2400) User: admin

Password: ***** （缺省口令通常是admin） NOTICE

NOTICE -- This switch has active licenses that will expire in 26 days NOTICE

NOTICE -- See 'show license' for details. NOTICE

(Aruba2400) >en

Password:***** （缺省口令通常是admin） (Aruba2400) #

恢复出厂值：

(Aruba2400) #write erase

All the configuration will be deleted. Press 'y' to proceed :

Write Erase successful (Aruba2400) #reload

Do you really want to reset the system(y/n): y ―――――――― Aruba交换机重启 ――――――――

初始化配置：

Enter System name [Aruba2400]:

Enter VLAN 1 interface IP address [172.16.0.254]: Enter VLAN 1 interface subnet mask [255.255.255.0]: Enter IP Default gateway [none]:

Enter Switch Role, (master|local) [master]:

Enter Country code (ISO-3166), for supported list: CN You have chosen Country code CN for China (yes|no)?: y Enter Password for admin login (up to 32 chars): ***** Re-type Password for admin login: *****

Enter Password for enable mode (up to 15 chars): ***** Re-type Password for enable mode: *****

Do you wish to shutdown all the ports (yes|no)? [no]:

Current choices are:

System name: Aruba2400

VLAN 1 interface IP address: 172.16.0.254 VLAN 1 interface subnet mask: 255.255.255.0 IP Default gateway: none Switch Role: master Country code: CN Ports shutdown: no

If you accept the changes the switch will restart!

Type to go back and change answer for any question Do you wish to accept the changes (yes|no)y Creating configuration... Done.

保存配置文件： (Aruba2400) >en Password:*****

(Aruba2400) #configure t

(Aruba2400) # copy running-config tftp: 192.168.4.100 aruba2400-0904.cfg

恢复配置文件： (Aruba2400) >en Password:*****

(Aruba2400) #configure t

(Aruba2400) (config) #copy tftp: 172.16.0.100 aruba2400-0904.cfg flash: 2400.bak (Aruba2400) (config) #copy flash: 2400.bak flash: 2400.cfg

(Aruba2400) (config) #boot config-file 2400.cfg (Aruba2400) (config) #reload

Do you really want to reset the system(y/n): y System will now restart!

Image 升级：

(Aruba200) #show boot Config File: default.cfg

Boot Partition: PARTITION 0

(Aruba2400) #show image version

(Aruba2400) #copy tftp: 172.16.1.50 A2400_FCS2.0.X_6577 system: partition 1 Upgrading partition 1

(Aruba2400) #reload

(Aruba200) #boot system partition 0 PC：

telnet 172.16.0.254 2300 connect 1/2 重启AP 4秒内Stop >purgenv >boot

login as: admin

admin@10.3.22.20's password: (Aruba-master) >enable Password:******

(Aruba-master) #configure terminal

Enter Configuration commands, one per line. End with CNTL/Z

(Aruba-master) (config) #telnet soe

Once SOE is enabled, you can connect to the AP serial port with the following procedure:

1 2 3

Telnet to the Aruba mobility controller using port 2300 Log in using the admin account

Connect to the Ethernet port that the AP is attached to

User: admin Password: ***** Available commands: connect exit (no args) soe> connect 2/0

Connecting to 2/0 at 9600 baud 8N1 Type \